Guide

Fixing Ethernet Connection Issues in Windows 11 and 10

Les imprimantes7 min de lecture
Fixing Ethernet Connection Issues in Windows 11 and 10

Quick answer: to fix an Ethernet connection that isn’t working in Windows 11 or 10, work through these steps in order and test after each one:

  1. Check the cable: plug it firmly into a LAN port on the router (not the WAN/Internet port) and try another cable.
  2. Restart the modem and router: unplug them for 30 seconds, then restart the modem first, then the router.
  3. Run the troubleshooter: open the Get Help app and run the Network and Internet troubleshooter.
  4. Reset the network stack: in an administrator Command Prompt, run netsh winsock reset, netsh int ip reset, ipconfig /release, ipconfig /renew and ipconfig /flushdns, then restart.
  5. Reinstall the Ethernet driver in Device Manager, and as a last resort use Settings › Network & internet › Advanced network settings › Network reset.
Sommaire
  1. Step 0: identify the symptom
  2. 1. Check the cable, ports and router
  3. 2. Restart the modem, router and PC
  4. 3. Check the status in Windows
  5. 4. Reset the network stack with commands
  6. 5. Fix DNS, proxy and VPN problems
  7. 6. Update or reinstall the Ethernet driver
  8. 7. Ethernet keeps disconnecting
  9. 8. Ethernet is slow
  10. 9. Last resort: network reset
  11. FAQ
  12. Related guides

Step 0: identify the symptom

The message Windows shows tells you where to look first.

Symptom Likely cause Go to
“Network cable unplugged” or no lights on the port Cable, port, adapter disabled Physical checks
“Unidentified network” or “No Internet” No IP address from the router (DHCP), IP stack Network commands
Connected, but websites don’t load DNS, proxy, VPN DNS and proxy
Ethernet keeps disconnecting Power saving, worn cable, driver Connection drops
Slow wired speed (100 Mbps instead of 1 Gbps) Cable category, damaged pair, port Slow Ethernet
Ethernet adapter missing in Windows Driver, adapter disabled in BIOS Driver

1. Check the cable, ports and router

  • Reseat the cable at both ends until it clicks. Look at the port lights: no light usually means no physical link.
  • Use a LAN port on the router, not the port labelled WAN, Internet or with a globe icon.
  • Swap the cable and try another router port. A bent connector or broken clip is a common culprit.
  • Remove extras: connect directly to the router, without a switch, wall socket or powerline adapter, to rule them out.
  • USB or dock adapter: plug it straight into the PC, not into a USB hub.

2. Restart the modem, router and PC

  1. Turn off the PC, the router and the modem (or your all-in-one internet box).
  2. Wait about 30 seconds.
  3. Turn on the modem and wait until its lights are stable, then the router, then the PC.

Test with Wi-Fi: if your phone or another device has internet on the same router, the problem is on the PC side.

3. Check the status in Windows

  1. Open Settings › Network & internet (Windows + I).
  2. Ethernet should say Connected. If you see Action needed or Not connected, select Ethernet to see the details.
  3. Go to Advanced network settings and make sure the Ethernet adapter is enabled (if it says Disabled, select Enable).

Then run the built-in troubleshooter: open the Get Help app and search for the Network and Internet troubleshooter.

4. Reset the network stack with commands

Search for Command Prompt, select Run as administrator, then run these commands one by one:

netsh winsock reset
netsh int ip reset
ipconfig /release
ipconfig /renew
ipconfig /flushdns

Restart the PC afterwards. To check the result, run ipconfig:

IPv4 address shown Meaning
192.168.x.x or 10.x.x.x Normal: the router gave the PC an address
169.254.x.x The PC did not receive an address: check the cable, the router, and that the adapter is set to Obtain an IP address automatically
No address / “Media disconnected” No physical link: back to step 1

5. Fix DNS, proxy and VPN problems

If Ethernet is connected but pages won’t load:

  • Test the connection: run ping 8.8.8.8. If it answers but websites don’t open, DNS is the problem.
  • Change DNS: Settings › Network & internet › Ethernet › DNS server assignment › Edit › Manual › IPv4 on, then enter for example 1.1.1.1 and 8.8.8.8.
  • Check the proxy: Settings › Network & internet › Proxy. Leave Automatically detect settings on and turn off any manual proxy you don’t recognise.
  • VPN and security software: temporarily disconnect the VPN. If a third-party firewall blocks everything, update it or check its network settings.

6. Update or reinstall the Ethernet driver

  1. First, download the Ethernet (LAN) driver from your PC or motherboard manufacturer’s site, in case Windows doesn’t reinstall it.
  2. Right-click Start › Device Manager › expand Network adapters.
  3. Right-click your Ethernet adapter (for example Realtek PCIe GbE or Intel Ethernet Controller) › Uninstall device.
  4. Check Attempt to remove the driver for this device, select Uninstall, then restart the PC.
  5. If the adapter does not come back, install the driver you downloaded.

Adapter missing completely? Select View › Show hidden devices in Device Manager. If it still isn’t there, check that the onboard LAN is enabled in the BIOS/UEFI. A missing adapter after a Windows update can also point to a failed update: see pending Windows updates (in French).

7. Ethernet keeps disconnecting

  • Power saving: Device Manager › Ethernet adapter › Properties › Power Management › uncheck Allow the computer to turn off this device to save power.
  • Energy-efficient Ethernet: on the Advanced tab, set options such as Energy-Efficient Ethernet or Green Ethernet to Disabled (names vary by manufacturer).
  • Cable: replace an old, crushed or very long cable.
  • Driver: install the latest driver from the manufacturer rather than a generic one.

8. Ethernet is slow

Check the link speed in Settings › Network & internet › Ethernet (Link speed).

Cable Maximum speed Verdict
Cat 5 100 Mbps Replace
Cat 5e 1 Gbps Fine for most connections
Cat 6 / 6a 1 to 10 Gbps Recommended

A 1 Gbps adapter stuck at 100 Mbps usually means a damaged cable or connector (one broken pair), a Cat 5 cable, or a 100 Mbps port on the router or switch.

9. Last resort: network reset

  1. Open Settings › Network & internet › Advanced network settings › Network reset.
  2. Select Reset now, confirm with Yes and let the PC restart.

Network reset reinstalls all network adapters and restores default settings. Afterwards, reinstall any VPN client or virtual switch, re-enter your Wi-Fi passwords and set the network profile to Private on your home network.

Still not working? Connect another PC to the same cable and port. If it works, the problem is your PC (adapter or system); a USB-to-Ethernet adapter is a cheap workaround. If it fails too, the issue is the router, the cable run or your internet provider.

Case study (typical example): a desktop PC showed “Unidentified network” after a router change, while Wi-Fi worked on other devices. ipconfig showed a 169.254.x.x address: the PC was not getting an IP. The adapter had a manual IP left over from the old router. Fix: Ethernet settings › IP assignment back to Automatic (DHCP), then ipconfig /renew. Connected in 5 minutes. [Replace with a real case from your support work: PC model, Windows version, symptom, fix.]

FAQ

Why is my Ethernet connected but there’s no internet?

The PC is linked to the router but can’t reach the internet: the router has no internet, the PC has no valid IP address, or DNS fails. Restart the modem and router, run ipconfig /renew and ipconfig /flushdns, and test with ping 8.8.8.8.

What does “Unidentified network” mean on Ethernet?

Windows didn’t receive an IP address from the router, usually shown as 169.254.x.x. Check that IP assignment is set to Automatic (DHCP), restart the router and reset the network stack.

How do I reset my Ethernet adapter in Windows 11?

Go to Settings, Network and internet, Advanced network settings, then Disable and Enable the adapter. For a full reset, use Network reset on the same page or reinstall the driver in Device Manager.

Why does Ethernet keep disconnecting?

Most often because of power saving on the adapter, a worn cable or an outdated driver. Disable power saving and Energy-Efficient Ethernet, replace the cable and update the driver.

Why is my Ethernet stuck at 100 Mbps?

The cable is Cat 5 or damaged, or the router or switch port is limited to 100 Mbps. Use a Cat 5e or Cat 6 cable and another port.

Do I lose data with a network reset?

No, your files stay. Network reset only removes network settings: Wi-Fi passwords, VPN clients and virtual adapters must be set up again.

Can a bad cable cause Ethernet problems?

Yes. A cable with a broken clip or damaged wire can cause no connection, drops or a 100 Mbps link. Swapping the cable is the fastest test.

A ramoz, IT technician and author at les-imprimantes.com I’ve been working as an IT technician for 12 years, handling troubleshooting, setup and security for Windows computers, networks and printers, for both individuals and businesses. Specializing in [printers and peripherals / networking / cybersecurity], I’ve installed, repaired and configured hundreds of devices, which taught me that the best solution is often the one that’s simplest to explain. On this blog, I share step-by-step guides, tested on real machines, to help you solve your IT problems without unnecessary jargon. Every tutorial is checked on current versions of Windows before publication.